Ads: Get Admission into 200 Level and Study any Course in any University of Your Choice. Low Fees | No JAMB UTME. Call 09038456231

WAEC GCE Metal Work Questions 2020 Objective and Theory Updates.

Filed in Exam, WAEC News by on February 4, 2020


WAEC GCE Metal Work Questions 2020 Objective and Theory Updates.

WAEC Metal Work Questions 2020: Metal Work WAEC GCE Expo Questions is out now on our website. In this article, I will be showing you past WAEC GCE Metal Work random repeated questions for free. You will also understand how WAEC GCE Metal Work questions are set and many more examination details. All you need to do is to stay focus and follow this guide.

The West African Examinations Council (WAEC) is an examination board that conducts the West African Senior School Certificate Examination, for University and Jamb entry examination in West Africa countries. … In a year, over three million candidates registered for the exams coordinated by WAEC.

WAEC Metal Work Questions 2020


There will be three papers, Papers 1, 2 and 3, all of which must be taken. Papers 1 and 2 will be a composite paper to be taken at one sitting.

PAPER 1: Will consist of forty multiple-choice objective questions all of which must be
answered within 1 hour for 40 marks.

PAPER 2: Will consist of five essay-type questions. Candidates will be required to answer four questions within 1 hour 30 minutes for a total of 60 marks.

PAPER 3: Will consist of two practical works, one of which must be carried out by candidates within 3 hours for 100 marks. Candidates shall be allowed 10 minutes, prior to the commencement of the test to study the drawings.

DISCLAIMER! These are not real WAEC GCE Metal Work questions but likely repeated questions over the years to help candidate understand the nature of their examinations. Ensure to take note of every questions provided on this page.

They will be required to make a test piece for which the appropriate drawings will be supplied. Schools will be required to supply materials needed for the test of their candidates.


1. Which of the following should be worn when pouring molten metal?
A. Shield
B. Helmet
C. Mask
D. Goggles

2. Which of the following materials is suitable for forging?
A. Cast iron
B. Brass
C. Mild Steel
D. Bakelite

3. The tool labeled Xis known as
A. Creasing iron.
B. Bick iron.
C. Funnel stake.
D. Hatchet stake.

4. The operation being carried out on workpiece Y is called
A. Raising.
B. Wiring.
C. Beading.
D. Bending.

5. The sand used for making moulds is
A. Dry sand.
B. Facing sand.
C. Green sand.
D. Parting sand.

6. The statement that defines the requirements of an artifact is referred to as
A. Brief.
B. Specification.
C. Analysis.
D. Situation.

7. The operation performed using the tailstock is
A. Drilling.
B. Turning.
C. Parting off.
D. Screw cutting.

8. The micrometer reading indicated in the figure is
A. 10.02 mm.
B. 10.15 mm.
C. 10.20 mm.
D. 10.67 mm.

9. Which of the following materials will require curburizing during heat treatment?
A. High carbon steel
B. High speed steel
C. Mild steel
D. Cast iron


1. (a) State one use of the following parts of the centre lathe.
(i) Tail stock
(ii) Tool post
(iii) Carriage
(iv) Head stock

(b) Sketch the parting off tool.
(c) State two safety precautions to be observed when operating the centre lathe.

If you need us to help you with more updated information at the right time about WAEC Metal Work Questions 2020, kindly provide us your phone number and email Address in the comment box below. Also feel free to ask any question pertaining to this guide.

What’s your take on this? We believe this article was interesting right, if yes, don’t hesitate using our share button below to inform – friends and relation via Facebook and twitter.

CSN Team.

Enter your email address:

Delivered by TMLT NIGERIA

Join Over 500,000+ Readers Online Now!



COPYRIGHT WARNING! Contents on this website may not be republished, reproduced, redistributed either in whole or in part without due permission or acknowledgement. All contents are protected by DMCA.
The content on this site is posted with good intentions. If you own this content & believe your copyright was violated or infringed, make sure you contact us at [[email protected]] to file a complaint and actions will be taken immediately.

Tags: , , , ,

Comments (1)

Trackback URL | Comments RSS Feed

  1. Felix says:

    its really a good one. please send the complete pass questions papers to me on metal work. Thanks