How to Gut a Deer (Best Techniques to Field Dress a Deer)

Learn how to gut a deer in a few simple steps. We wish to provide you with everything necessary for you to do this task quickly. See the crucial stages of completing it by reading on.

How to gut a deer

How to Gut a Deer

Once your deer is on the ground, another hurdle is dissecting the corpse and making it ready to eat.

This post will show you how to field dress a deer effectively so that you may store meat in your freezer.

Steps to Gut a Deer

Here are the detailed instructions on how to field dress a deer.

1. Skinning Process

In order to skin the deer, hang it. A tractor with a lift or bucket or a tent with a winch and frame would be ideal for lifting the deer up.

A potable water system with a garden hose and sprayer is preferred. You also need to have a lot of clean water on hand.

A thick rope or strap should be tied as far up the neck as you can around the animal’s antlers or beneath its head.

The procedures are the same, however, some hunters like to hang their deer by the achilles tendons with the head down.

With the head hanging up, the stomach, intestines, and bladder can be removed more easily and with less risk of contaminating the meat.

2. Taking the Organs Out

As soon as you can after you shoot your deer, field dress it. The greatest approach to completely using the nutritional benefits of the once-living animal is in this manner.

The internal organs must be removed, and the carcass must be cooled, in order to prevent the meat from becoming bad.

Starting from the bottom, or pelvis, upward, gut the deer by cutting the stomach membrane.

Prepare to have the organs removed. Reach into the abdomen and remove the organs after splitting up to the base of the sternum.

In the lower region of the abdomen, look for the bladder close to the spine. It will resemble a transparent balloon that has a yellow liquid inside of it (urine).

Take out the intestines and anus. Cut a circle around the anus with your knife that is about 1 inch (2.5 cm) in diameter. How to Gut a Deer

Split the sternum or the ribcage’s middle. Use a saw or a broad, sturdy knife appropriate for the job. If you plan to save the chest for nourishment, spread it open while being cautious not to let the heart fall out.


3. Skinning the Deer

Each hoof should first be taken off at the elbow. Locate the joint with the tip of your knife and cut it.

Cut through the skin starting at the animal’s skull base. After that, trim the area around the base of the neck.

The breastbone, the stomach, the pelvis, and the forelegs. Start removing the skin from the neck and shoulders. As you descend, move your way toward the chest.

The skin should be removed from the corpse either mechanically or by hand.

When peeling by hand, pull the skin down a little before slicing the tissue and connecting it to the muscles underneath it.

Lay the deer out on a level work surface after taking it down. Cut the ligaments just behind the jaw to release the neck’s connective tissue.

To break the neck and fully remove the head, you’ll need to twist it violently.

After the skin is taken off, rinse the deer’s carcass. This will assist chill the meat while you finish the task and remove any hair that has become trapped in the meat.

4. Aging the Meat

After thoroughly cleaning the venison with cold water. Locate a place where you can age well.

Finding a room large enough for your deer and with temperature control is the most challenging step in the procedure.

Hang the carcass. Attach the meat to a strong rafter in your aging area using a meat hook, chain, and rope.

The meat should be aged for a week or more. Similar to beef, the collagen in the muscle cells of aged meat breaks down.

Letting the meat remain for a week in a cool area with sufficient air circulation substantially enhances the quality and flavor of the venison. How to Gut a Deer

5. Disassembling the Deer

Set up a spotless work area and gather your equipment. A big cleaver and a boning knife come in handy for this job.

Make sure your equipment is well kept and sharp, and that your work area is sanitary and wide enough to accommodate huge quantities of meat.

To remove the chuck meat (front quarters) from the round, split the backbone (hind quarters).

Tenderloins and backstraps should be removed. The tenderloins are the dark, lean, red flesh located inside the cavity, running alongside the backbone, and are perhaps the most delicate and flavorful cut of deer.

All the way down the backbone, close to the spine, a saw was used to cut through the ribs. Remove the flesh of the neck and shoulder.

Disconnect the hock joints from the hams. The remaining leg flesh above the joint where the hooves were removed is known as the hocks, while the hams of the deer are the fatty meat located around the animal’s rear hips or rump.

6. Storage

Get it ready for freezing. Remove any fat, cartilage, bruises, discoloration, and dry areas brought on by aging with an extremely sharp boning knife.

Prepare the slices you intend to consume. When you’re ready to thaw it and start cooking, the meat will be at the ideal stage for butchering, which will help save time.

Defrost the meat. The meat should be placed in plastic freezer bags in amounts that correspond to meals.

Prior to putting the bags in the freezer, make sure the bags are well packed and that as much air has been squeezed out as possible.

Kill nothing you won’t consume or want to share with others. If the deer is to be caped for mounting, we should not follow the procedures for skinning the neck and shoulders. How to Gut a Deer

While operating, keep your saw and knives clean and in good condition. This expedites the process significantly.

Was this article useful? Leave a comment. And don’t forget to share.

CSN Team.

Similar Posts